Centrifugal pumps in Marine Engineering on ships

Centrifugal pump principles and working procedure

A pump is a machine used to raise liquids from a low point to a high point. In a centrifugal pump liquid enters the centre or eye of the impeller and flows radially out between the vanes, its velocity being increased by the impeller rotation. A diffuser or volute is then used to convert most of the kinetic energy in the liquid into pressure.

The arrangement of a centrifugal pump is shown diagrammatically in figure below

Centrifugal pump

Fig: Centrifugal pumping operation

A vertical, single stage, single entry, centrifugal pump for general marine duties is shown in Figure here. The main frame and casing, together with a motor support bracket, house the pumping element assembly. The pumping element is made up of a top cover, a pump shaft, an impeller, a bearing bush and a sealing arrangement around the shaft. The sealing arrangement may be a packed gland or a mechanical seal and the bearing lubrication system will vary according to the type of seal. Replaceable wear rings are fitted to the impeller and the casing. The motor support bracket has two large apertures to provide access to the pumping element, and a coupling spacer is fitted between the motor and pump shaft to enable the removal of the pumping element without disturbing the motor. 

Single entry centrifugal pump

Fig: Single entry centrifugal pump

A vertical multi-stage single-entry centrifugal pump used for deep-well cargo pumping is shown in Figure below. This can be considered as a series of centrifugal pumps arranged to supply one another in series and thus progressively increase the discharge pressure. The pump drive is located outside the tank and can be electric, hydraulic or any appropriate means suitable for the location.

Multi stage centrifugal pump

Fig: Multi stage centrifugal pump

A diffuser is fitted to high-pressure centrifugal pumps. This is a ring fixed to the casing, around the impeller, in which there are passages formed by vanes. The passages widen out in the direction of liquid flow and act to convert the kinetic energy of the liquid into pressure energy. Hydraulic balance arrangements are also usual. Some of the high-pressure discharge liquid is directed against a drum or piston arrangement to balance the discharge liquid pressure on the impeller and thus maintain it in an equilibrium position.

Centrifugal pumps, while being suitable for most general marine duties, are not self priming and require some means of removing air from the suction pipeline and filling it with liquid. Where the liquid to be pumped is at a level higher than the pump, opening an air cock near the pump suction will enable the air to be forced out as the pipeline fills up under the action of gravity. If the pump is below sea water level, and sea water priming is permissible in the system, then opening a sea water injection valve and the air cock on the pump will effect priming.

Alternatively an air pumping unit can be provided to individual pumps or as a central priming system connected to several pumps. The water ring or liquid ring primer can be arranged as an individual unit mounted on the pump and driven by it, or as a motor driven unit mounted separately and serving several pumps. The primer consists of an elliptical casing in which a vaned rotor revolves. The rotor may be separate from the hub and provide the air inlet and discharge ports as shown in Figure down. Alternatively another design has the rotor and hub as one piece with ports on the cover. The rotor vanes revolve and force a ring of liquid to take up the elliptical shape of the casing. The water ring, being elliptical, advances and recedes from the central hub, causing a pumping action to occur. The suction piping system is connected to the air inlet ports and the suction line is thus primed by the removal of air. The air removed from the system is discharged to atmosphere. A reservoir of water is provided to replenish the water ring when necessary.

Water-ring primer

Fig: Water-ring primer

When starting a centrifugal pump the suction valve is opened and the discharge valve left shut: then the motor is started and the priming unit will prime the suction line. Once the pump is primed the delivery valve can be slowly opened and the quantity of liquid can be regulated by opening or closing the delivery valve. When stopping the pump the delivery valve is closed and the motor stopped.

Regular maintenance on the machine will involve attention to lubrication of the shaft bearing and ensuring that the shaft seal or gland is not leaking liquid. Unsatisfactory operation or loss of performance may require minor or major overhauls. Common faults, such as no discharge, may be a result of valves in the system being shut, suction strainers blocked or other faults occurring in the priming system. Air leaks in the suction piping, a choked impeller or too tight a shaft gland can all lead to poor performance.

When dismantling the pump to remove the pumping element any priming pipes or cooling water supply pipes must be disconnected. Modern pumps have a coupling spacer which can be removed to enable the pumping element to be withdrawn without disturbing the motor: the impeller and shaft can then be readily separated for examination. The shaft bearing bush together with the casing and impeller wear rings should be examined for wear. 


Write to me at marinenotes4u@gmail.com,283928@gmail.com.::MK::.

Facebook:Marine NotesTwitter:ACMWCTRss:ACMWCT
Marine Notes - MMD Exams India and Baiscs
URL: HTML link code: BB (forum) link code:
© Marine Notes - MMD Exams India and Basics (M&K Groups Ltd)


Unknown said...

Nice blog thanks for posting.
Purohit Enterprises major Stockiest & Trader of submersible and non submersible, centrifugal, vertical pumps for various applicationsCentrifugal Pumps

Unknown said...

hey nice source for us,thanks for sharing this information.Centrifugal pumps are used to move liquids in the pipe lines and its main applications are in petrochemical industries, chemical plants, process control industries and water treatment plants.

Centrifugal Pump||Centrifugal Water Pump

Unknown said...

Loved this article. Would surely take the advantage.
high pressure centrifugal pump manufacturer india

Unknown said...

With the help of the diagram i can know easier about the functioning of the pumps. Thanks for sharing.
industrial water pumping in coimbatore | electric pumps in coimbatore

kayblowers said...

Hey I am so grateful I found your site, I really found you
by error, while I was browsing on Digg for something else, Anyhow I
am here now and would just like to say thank you for a incredible post and a all round enjoyable blog

Mechanical boosters
Industrial blowers

Matthew Bajada said...

I am working in a ship as a driver. A ship requires various pumping system to control the machinery operation at sea. Some system supply coolant or lubricant to the main machinery, Some are used to supply and discharge the water (fresh/sea water). So i used to buy reliable and quality range of Bilge Pumps Shower Pumps for boat which we can depend on.

Facebook Marine Notes
Twitter Marine Notes
Rss Marine Notes


Follow by Email